Series SY Dual-Voltage Hot Runner Control System
• The Series RMB or RMC control modules are available
for use
in the dual voltage mainframes
• Communications available with RMC control modules
• CE approval
• Wide range of accessories available for customization
of
control system
Series
IMP
• Simultaneous digital setpoint and digital temperature
indication
• Available in 15-amp modules as well as single-zone 15-
and
30-amp portable temperature controllers
• Athena’s Controllers are compatible with all D-M-E
Company’s
G SERIES and SMART SERIES® ITC, MCS, YUDO® and INCOE®
brand mainframes.
• CompuStep® feature removes moisture from the heater
before
full power is applied
• CompuCycle® feature improves response time, reduces
thermal fatigue and prolongs heater life by applying AC
power smoothly and continuously
• Manual control for non-thermocouple applications,
provides
standby or “weekend” heat or to manually control temperature if a
thermocouple fails
• Diagnostic and protection features include power “on,”
power to load, manual made, and
over/under temperature, plus indicators and system protection for
reversed and open
thermocouples
• SafeChange
™ “hot swap”
feature allows safe removal and replacement of module
Series
RMA
• Compatible with industry standards
control modules and
mainframes
• Accepts Type J thermocouple
• Bumpless auto/manual transfer
• CompuStep® bake out feature prevents moisture at
startup
• Built-in loop break for open heater, shorted triac,
reversed or
shorted thermocouple
• Open thermocouple break protection with
jumper-selectable
shutdown or average power output based on operation
• Preset alarms at 30°F (17°C)
• SafeChange™ “hot swap” feature allows safe removal and
replacement of module
• CE compliant
Series
RMB
• Athena’s mainframes are compatible with all D-M-E
Company’s G SERIES and SMART SERIES,® ITC, MCS, YUDO®
and INCOE® brand mainframes.
• Accepts Type J or Type K thermocouple input (jumper-
selectable)
• Auto-tuning, with adjustable proportional band and
rate
• Bumpless auto/manual transfer
• CompuStep® bake out feature prevents moisture at
startup
• Built-in loop break, short, open, and reverse
thermocouple
protection
• Built-in triac safety protection
• Ground-fault protection
• Preset alarms at 30° F (17°C)
• Jumper-selectable soft-start mode
• Current monitor feature displays average current to
load
• SafeChangeTM “hot swap” feature allows safe removal
and
replacement of module
• CE compliant
Series
RMC
• Choice of three default modes for open thermocouple
condition
• Built-in triac safety protection
• Accepts J or K thermocouple input (jumper selectable)
• SafeChangeTM “hot swap” feature allows safe removal
and
replacement of module
• CompuStep® bake out feature prevents moisture at
startup
• Built-in loop break, short, open, and reverse
thermocouple
protection
• Boost” mode for temporary % of power output increase
• Ground-fault protection
• Adjustable setpoint limits
• Stores highest temperature detected
• Current monitor feature displays average current to
load
• CE compliant
Series
RMT
• Accepts Type J thermocouple
• Bumpless auto/manual transfer
• CompuStep® bake out feature prevents moisture at
startup
• Built-in loop break for open heater, shorted triac,
reversed or shorted thermocouple
• Open thermocouple break protection with
jumperselectable shutdown or average power output based
on operation
• Preset alarms at 30°F (17°C)
• SafeChange™ “hot swap” feature allows safe removal and
replacement of module
• CE compliant
• 15 amps per zone
Hot Runner Control System Transformer Kits
Transformer kits are fully wired and include enclosed
transformer (480 Vac 30 in, 240 Vac 30 out) with
adjustable voltage taps, power cable to main frame,
disconnect switch, extra fuses, and floor stand with all
hardware. Other transformers are available for your
particular power requirements.
- 6 KVA
- 9 KVA
- 15 KVA
- 30 KVA
- 45 KVA
Thermocouple Connectors
- 5 Zones
- 8 Zones
- 12 Zones
Mold Power/Input Connectors
- 5 Zones
- 8 Zones
- 12 Zones
MTC
Terminal Mounting Boxes for Thermocouple Connectors
- 5 Zones
- 8 Zones
- 12 Zones
PICL
and PICH Terminal Mounting Boxes for Mold Power Input
Connectors (15 amps)
- 5, 8, or 12 Zones
- 5 Zones (CE only)
- 8 Zones (CE only)
- 12 Zones (CE only)
Mold
Thermocouple Cable
- 5 Zones
- 8 Zones
- 12 Zones
Length 10', 20'
Mold
Power Cable (15A)
- 5 Zones Zones
- 8 Zones
- 12 Zones
Length 10', 20'